Radiator

1968, 1969, and 1970 Mustangs originally equipped with a 428 engine were also originally equipped with a heavy-duty "extra cooling" 3-row engine coolant radiator. These down flow radiators were built with vertical tubes and a corrugated-fin core for vertical flow of the coolant from top to bottom. The core is capped with header tanks at top and bottom. The radiator inlet port (upper header tank) connects to the thermostat housing on the engine. The radiator outlet port (lower header tank) connects to the water pump inlet port. The bottom header tank on automatic transmission cars includes two ports and a heat exchanger for cooling of the transmission fluid; these parts are absent on original radiators installed in cars equipped with a manual transmission. Service replacement radiators typically include the ports and heat exchanger when they're intended for use with either type of transmission. The ports can be capped if they're not needed.

Radiator Rear

Rear View, 1970 Radiator

Radiator Front

Front View, 1970 Radiator

Radiator Ports

Transmission Fluid Cooler Ports

Ford commonly identified these radiators using stamped engineering numbers on the core frame. A stamped metal tag was sometimes placed on the core frame instead, perhaps due to a manufacturing change or modification. A date code is usually present.

Factory-Installed Radiator Identification

TransmissionEngineering NumbersService Part NumberCore Dimensions
ManualC8ZE-L, -L1, -L2C8ZZ-8005-C2 1/4" deep, 16" tall, 24 3/16" wide
AutomaticC8ZE-M, -M1, -M2
C8ZE-S1
C8ZZ-8005-C2 1/4" deep, 16" tall, 24 3/16" wide

The factory-installed radiator used in 428 CJ Mustangs was also used in 1969 and 1970 Boss 429 Mustangs and 1968 - 1970 Mercury Cougars equipped with a 428 CJ. Note that Ford used the same C8ZZ-8005-C service part number for both automatic and manual transmission applications.

My 1974 OSI manual notes that the C8ZZ-C radiator replaced an earlier C8ZZ-A radiator. I have a sneaking suspicion that the -A radiator was the original manual transmission replacement radiator.

Ford vehicles equipped with 390 and 428 engines commonly received different radiators during factory assembly. However, Ford used the same service replacement radiator part numbers for a number of 390 and 428 vehicle applications to reduce inventory and service complexity. The C8ZZ-C service part number can be cross-referenced to engineering numbers C8ZE-K, C8ZE-M, C8ZE-S, and C9ZE-AE. The C8ZZ-A service part number can be cross-referenced to engineering numbers C8ZE-A, C8ZE-B, C8ZE-C, and C8ZE-L. Ultimately, this means that a buyer of a replacement C8ZZ-C radiator could have received a radiator with any of these stamped engineering numbers.

I've received info from JD Larson of All Classic Motors that suggests that there were two major suppliers of these radiators: Modine and West Modine. Modine radiators appear to have been used primarily at the Dearborn and Metuchen assembly plants. They are easily identified by a FoMoCo logo on the top tank and an engineering number and date code on one of the side rails, usually (but not always) the passenger-side side rail. West Modine (W MO) radiators appear to have been used exclusively at the San Jose assembly plant. Most, but not all, of these radiators have a FoMoCo logo on the top tank. The top tank has an embossed "W MO" stamping with a date code just below. Date codes are either embossed or stamped. The engineering number will be embossed on the top tank or it will be embossed or stamped onto a small brass tag that is soldered to the top tank, normally on the passenger side.

Here are some pictures of tags and other identifying marks:

Radiator Tag C8ZE-L2

C8ZE-L2 Tag

C8ZE-L

C8ZE-L Stamp with 9HC (August 1969, 3rd week) date Code

C8ZE-M1

C8ZE-M1 Stamp with 7HA (August 1967, 1st week) date Code

C8ZE-S1 Stamp9LD (November 1969, 4th week) Date Code
C8ZE-S19LD Date Code

FoMoCo Tank Stamp

I've also received reports of some top tanks having a small tag soldered in place near the fill opening. This particular tag was found on a radiator pulled from a 1970 Mustang built at Dearborn. I don't yet know what this tag identifies or how to decode it, but some have suggested that it might have been added when the radiator was serviced. Here are two pictures:

Radiator Tank TagRadiator Tank Tag
(close up)
Tank TagTank Tag

Here are two pictures of West Modine radiator markings with different date codes. These marks are typically covered with a mounting bracket when the radiator is installed in a car:

"W MO" 67-12 (December 1967)"W-MO" 12 68 (December 1968)
WMO 1WMO 2

JD has also seen original Modine radiators built for Ford that were re-stamped or re-tagged to suit a later assembly or service application. For example, a C7OE was changed to C8OE by soldering a small brass tag with an "8" on it to the side rail engineering number. Here are two examples:

-S1 Tag-S1 Tag and Original Stamping

Some last details: notice the fitting near the fill opening in the picture below. This fitting normally has a rubber hose attached to it that runs down the side of the radiator to direct overflow coolant to the ground. There's no coolant recovery tank. The proper fill level is just to the top of the tubes. While this may look low, remember that you need to leave some room for expansion. Over-filling the radiator will usually cause some "burping" of coolant until the system reaches the proper level.

Radiator Front